What are your opinions concerning How to Install a Bathtub?
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily obtainable, the task can relocate immediately; if you have to open up a wall to eliminate the old tub and position the new tub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old bathtub and also set in the new one. Make sure you have actually certified yourself for the work and fit trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your washroom if you have actually already bought a new bathtub and do not need to alter the setup of your previous water supply pipes.
Your devices and product list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The previous type should be attached to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Utilizing the two wooden boards under its feet, place the bath tub in the required setting. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the tub until the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if necessary. Load the bath tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the producer's user's manual. Tiling and also sealing around the bath tub must wait up until the tub has been made use of a minimum of once as this will settle it into its final position.
Preparing for the Setup
Firstly, the supporting framework supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to avoid pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last placement.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, creating the water to pass through the wall in between the bath and the tiling, leading to issues with dampness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and also cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that editorial on Installing A Bathtub from an associate on a different web page. Make sure you set aside a second to share this content if you liked it. Thanks so much for taking the time to read it.
Emergency plumber? One call away.